- 24
- 134 426
Greg Zimmers
Приєднався 18 січ 2010
Відео
Hurricane Sally 2020 Miramar Beach Florida
Переглядів 1,8 тис.3 роки тому
Hurricane Sally 2020 Miramar Beach Florida
Unser Karting Memorial Day 2017
Переглядів 517 років тому
I created this video with the UA-cam Video Editor (ua-cam.com/users/editor)
How to Easily Change the Control Arm Bushing BMW E46
Переглядів 100 тис.9 років тому
How to easily remove an old control arm bushing without damaging your car in the process and without purchasing expensive special purpose tools. The repair was done on a 2005 BMW 330i E46
1967 Corvette Stingray C2 test drive HD GoPro
Переглядів 2,2 тис.9 років тому
Driving the 1967 Corvette Stingray 327 L79 with 350 horsepower
Boulder Front Range time lapse clouds rolling in
Переглядів 5911 років тому
The front range time lapse on the 4th of July, 2013.
Arduino control sprinkler 8 zones
Переглядів 7 тис.11 років тому
Controlling 8 zones for the sprinkler with an Arduino
Arduino IV-9 Numitron Tubes with TLC5940
Переглядів 38311 років тому
Arduino IV-9 Numitron tubes with TLC5940
English Bulldog thinks ice cubes are treats!
Переглядів 35212 років тому
English Bulldog thinks ice cubes are treats!
Control 24 volt sprinkler solenoid with an Ardiuno
Переглядів 2,8 тис.12 років тому
Control 24 volt sprinkler solenoid with an Ardiuno
Control Sprinkler Solenoid with Arduino
Переглядів 2,9 тис.12 років тому
Control Sprinkler Solenoid with Arduino
IV-9 Numitron with an Arduino and a TLC5940
Переглядів 81712 років тому
IV-9 Numitron with an Arduino and a TLC5940
FTC Bowled Over robotics scrimmage Fort Collins, Colorado
Переглядів 23812 років тому
FTC Bowled Over robotics scrimmage Fort Collins, Colorado
Netduino plus light LED simple example
Переглядів 1,4 тис.13 років тому
Netduino plus light LED simple example
Stunning!
I can assure you that there is no easy way to replace control arm bushings.
Great idea, i have one handy and didn't think about it. Thanks!!!!
Hello thank’s for this video Do you have the references of this tool? Where can we buy it ?
Thanks for the video man
Good day, I'm trying to build a similar circuit . Can you help me with the design and assembly ?
Thank you!
You can sometimes get away with a pipe wrench as well.
From Where i can buy the arm bushing tool remover?
2 jaw puller, search ebay or amazon
wd40 in the old bush first, then the whole thing comes off in one, put the new one in hot water for a while then put soapy water on mount and bush will go on with a hard push, takes 10 mins....
I wish you were my mechanic !! My guy said I need to leave the car all day to replace bushings for my 2004 bmw 325CI
He's a little buddy :-):-):-)
so how do I take these off without damaging them? lol
This is a part that degrades and needs replacing. Why take them off if they are in good shape?
replacing the control arm. My bmw e46 have inner ball joints that can't be pressed out as the back is solid unlike the front lower ball joint that has a quarter sized hole on the back for a ball joint press kit to easily push it out.. so I am having to replace the entire arm but the bushing are 100% good.. been trying to get them off without damaging them.. sofar no luck. :( stuborn bastards haha.
Yea, that is going to be tough. They are extremely stubborn. You might be replacing them along with your control arms.
Yeah just ordered the parts. Going for a full reinstall. Thank you for the surprisingly quick replies :D
Good luck with the repair
Hi, Can you please help me in setting up the whole system for 5HP motor irrigation system? I don't have any idea about the arduino system.
Hi, what brand of bushing do you recommend? Thanks. (2004 325i)
Meyle HD
Wish I had thought about getting that tool. Just attempted to pull the damn thing off after lubricating it and it didnt budge at all. Just had to put me car back together and warm up after freezing my ass of outside :(.
How much would a mechanic charge if I supply the bushings? Approx.
In dollars, it was 300$ for me
Hi could you tell me whats the size of your gear puller ? thanks
In the picture I thought I was ordering the whole lollipop. Opened the package and its just the bushings.......bastards......
What did expect for what you paid?
nicely done I do mine the exact same way. silicone spray is a must, makes things much easier and is good for the rubber.
Amazing video, thanks buddy! Keep those BMW videos coming.
Thank you, very helpful!
GOOD JOB!!
HI. I've got a TLC5940 and have it hooked up to my Arduino. I have it driving a 16-segment LED at the moment. I have a few IV-17 tubes I would like to drive with it but I can't find anything about how to wire them up. Would you happen to have a circuit schematic or anything I could use to point me in the right direction?
I lost track but my guess is between one and two hours.
How much time is compressed into the 15 seconds?
Do you have step by step instructions?
This looks very similar to what I am trying to build to control a series of aquarium lights. Could you post your arduino sketch? I'm having trouble setting up the lights to react to the RTS.
Yes. I have the tube and the RBG LED hooked up to the same TLC5940.
Nice, I like the RGB LEDs! Are you powering them with the same driver chips as the numitrons?
lol yes that is her snoring!
Nice :) Is that your dog snoring in the background?
I use Ragnarok Grey. You can get it here or several other website by search for Ragnarok Grey. studiostyl.es/schemes/ragnarok-grey
I use Ragnarok Grey. You can get it here or several other website by search for Ragnarok Grey. studiostyl.es/schemes/ragnarok-grey
awesome! What color theme are you using in visual studio? Im a professional asp.net C# developer and im sick of the white background - black text standard theme :)
A bit off topic, but what theme are you using for your coloring? Looks pretty good. Any chance you could export it or point us to it?